Impulse 3420 Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Hardware Impulse 3420. Impulse 3420 User Manual Manual do Utilizador

  • Descarregar
  • Adicionar aos meus manuais
  • Imprimir
Vista de página 0
COMM+8™
USER MANUAL
Part #3420
Sealevel Systems, Inc. Telephone: (864) 843-4343
PO Box 830 Fax: (864) 843-3067
Liberty, SC 29657 USA www.sealevel.com
Vista de página 0
1 2 3 4 5 6 ... 22 23

Resumo do Conteúdo

Página 1 - USER MANUAL

COMM+8™ USER MANUAL Part #3420 Sealevel Systems, Inc. Telephone: (864) 843-4343 PO Box 830 Fax: (864) 843-3067 Liberty, SC 29657

Página 2 - Contents

Card Setup Sealevel Systems COMM+8 Page 7 To select the maximum data rate (460.8K bps) place the jumper in the divide by 1 (silk-screen DIV1) positio

Página 3 - Figures

Installation Sealevel Systems COMM+8 Page 8 Installation Operating System Installation For Windows Users Start by choosing Install Software at the b

Página 4 - Introduction

Technical Description Sealevel Systems COMM+8 Page 9 Technical Description The Sealevel COMM+8 provides 8 additional serial ports for terminals, mode

Página 5

Technical Description Sealevel Systems COMM+8 Page 10 DB-25 Connector Pin Assignments (DB-25 Male) Signal Name Pin # Mode GND Ground 7 TD Transmi

Página 6 - Card Setup

Technical Description Sealevel Systems COMM+8 Page 11 DB-78 Connector Pin Assignments (DB-78 Female) Port # 1 2 3 4 5 6 7 8 TD 36 12 27 3 7

Página 7 - IRQ Selection

Specifications Sealevel Systems COMM+8 Page 12 Specifications Environmental Specifications Specification Operating Storage Temperature Range 0º to 50

Página 8 - Interrupt Mode Options

Appendix A - Troubleshooting Sealevel Systems COMM+8 Page 13 Appendix A - Troubleshooting Serial Utility test software is supplied with the Sealevel

Página 9 - Clock Modes

Appendix A - Troubleshooting Sealevel Systems COMM+8 Page 14 8. The following are known I/O conflicts: • The 278 and 378 settings may conflict wit

Página 10

Appendix B – How To Get Assistance Sealevel Systems COMM+8 Page 15 Appendix B - How To Get Assistance Please refer to Troubleshooting Guide prior t

Página 11 - Installation

Appendix C - Electrical Interface Sealevel Systems COMM+8 Page 16 Appendix C - Electrical Interface RS-232 Quite possibly the most widely used commu

Página 12 - Technical Description

Contents INTRODUCTION ... 1 OVERVIEW...

Página 13

Appendix D - Asynchronous Communications Sealevel Systems COMM+8 Page 17 Appendix D - Asynchronous Communications Serial data communications implie

Página 14

Appendix E - Silk-Screen Sealevel Systems COMM+8 Page 18 Appendix E - Silk-Screen 3.9"7.0"4.2"

Página 15 - Specifications

Appendix F - Compliance Notices Sealevel Systems COMM+8 Page 19 Appendix F - Compliance Notices Federal Communications Commission Statement FCC - Th

Página 16 - Appendix A - Troubleshooting

Warranty Sealevel Systems COMM+8 Page 20 Warranty Sealevel Systems, Inc. provides a limited lifetime warranty. Should this product fail to be in go

Página 17

FEDERAL COMMUNICATIONS COMMISSION STATEMENT...19 EMC DIRECTIVE STATEMENT ...19 WARRANTY.

Página 18

Introduction Sealevel Systems COMM+8 Page 1 Introduction Overview The Sealevel Systems COMM+8 provides the PC with eight RS-232 asynchronous ports. T

Página 19

Introduction Sealevel Systems COMM+8 Page 2 For your reference, record installed COMM+8 settings below: Port # Base Address IRQ E12 Port 1 Por

Página 20 - 5 to 8 Data Bits

Card Setup Sealevel Systems COMM+8 Page 3 Card Setup The COMM+8 contains several jumper straps that must be set for proper operation. Address Selecti

Página 21 - 3.9"

Card Setup Sealevel Systems COMM+8 Page 4 “PAL” Addressing If header E11 is set to the “PAL” position, the board can be addressed at a customized lo

Página 22 - EMC Directive Statement

Card Setup Sealevel Systems COMM+8 Page 5 Interrupt Mode Options The COMM+8 will allow each port to have an independent interrupt level or share an i

Página 23 - Warranty

Card Setup Sealevel Systems COMM+8 Page 6 Set all jumpers to “S” if you are using more than one COMM+8 in a bus or you wish to completely remove the

Comentários a estes Manuais

Sem comentários